setup_harddisks doesn't find any disk

[Jean-Paul BALOCHE]

Well,

Well, to start, some good news : I have configured a new fai server. Now
everything is ok for ata disk : I can install a demohost with ata, but
(bad news !) not with SATA.
The modules are now ok and they can be loaded.
When I try an installation with SATA, I've got those error messages :


In fai.log :
Calling task_defclass
10-base-classes      OK.
Discovering hardware: sata_nv tulip
Loading sata_nv:
Skipping tulip; assuming it is compiled into the kernel.
Video card detected: 
20-hwdetect.source   OK.
50-host-classes      OK.
Calling task_defvar
++ FAI_CONSOLEFONT=
++ FAI_KEYMAP=fr-latin1
++ UTC=yes
++ time_zone=Europe/Paris
++ rootpw=$1$kBnWcO.E$djxB128U7dMkrltJHPf6d1
++ moduleslist=usbkbd ehci-hcd ohci-hcd uhci-hcd usbhid psmouse
++ FAI_ACTION=install
Loading keymap(s) fr-latin1 ...done.
Calling task_action
FAI_ACTION: install
Performing FAI installation. All data may be overwritten!

Calling task_install
Calling task_partition
Partitioning local harddisks
setup_harddisks version 0.38fai
Probing disks: 
Disks found:

Using config file: /fai/disk_config/FAIBASE
ERROR: could not read device /dev/
Mapping disk name disk1 to 
setup_harddisks version 0.38fai
Probing disks: 
Disks found:

Using config file: /fai/disk_config/FAIBASE
Mapping disk name disk1 to 
cp: cannot stat `/var/log/fai/current/disk_var.sh': No such file or
directory
Save log files via rsh to fai at fai-v2:demohost/install-20060727_000151
rcmd: getaddrinfo: Name or service not known
rcmd: getaddrinfo: Name or service not known
setup_harddisks did not create /var/log/fai/current/disk_var.sh file.


-------------------------
in kernel.log :

klogd 1.4.1#17, log source = /proc/kmsg started.
Inspecting /boot/System.map-2.6.16-fai-kernels
Loaded 17531 symbols from /boot/System.map-2.6.16-fai-kernels.
Symbols match kernel version 2.6.16.
No module symbols loaded - kernel modules not enabled.

<6>NET: Registered protocol family 10
<6>IPv6 over IPv4 tunneling driver
<6>NFORCE-CK804: IDE controller at PCI slot 0000:00:06.0
<6>NFORCE-CK804: chipset revision 242
<6>NFORCE-CK804: not 100%% native mode: will probe irqs later
<6>NFORCE-CK804: 0000:00:06.0 (rev f2) UDMA133 controller
<6>    ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
<6>    ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
<7>Probing IDE interface ide0...
<4>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
<4>Warning: /proc/ide/hd?/settings interface is obsolete, and will be
removed soon!
<7>eth3: no IPv6 routers present
<6>usbcore: registered new driver usbfs
<6>usbcore: registered new driver usbkbd
<6>drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
<7>PCI: Setting latency timer of device 0000:00:02.1 to 64
<6>ehci_hcd 0000:00:02.1: EHCI Host Controller
<6>ehci_hcd 0000:00:02.1: debug port 1
<7>PCI: cache line size of 64 is not supported by device 0000:00:02.1
<6>usb usb1: configuration #1 chosen from 1 choice
<7>ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver
(PCI)
<6>ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
<6>ohci_hcd 0000:00:02.0: irq 10, io mem 0xf6002000
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 10 ports detected
<6>usbcore: registered new driver hiddev
<6>usbcore: registered new driver usbmouse
<6>drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
<5>SCSI subsystem initialized
<6>Fusion MPT SPI Host driver 3.03.07
<7>sata_nv 0000:00:07.0: version 0.8
<7>PCI: Setting latency timer of device 0000:00:07.0 to 64
<6>ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD008 irq 10
<6>ata2: SATA link down (SStatus 0)
<6>scsi1 : sata_nv
<6>ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xE400 irq 11
<6>ata3: SATA link up 1.5 Gbps (SStatus 113)
<3>irq 10: nobody cared (try booting with the "irqpoll" option)
<4> [__report_bad_irq+43/105] __report_bad_irq+0x2b/0x69
<4> [note_interrupt+402/451] note_interrupt+0x192/0x1c3
<4> [handle_IRQ_event+34/78] handle_IRQ_event+0x22/0x4e
<4> [__do_IRQ+157/207] __do_IRQ+0x9d/0xcf
<4> [do_IRQ+25/36] do_IRQ+0x19/0x24
<4> [common_interrupt+26/32] common_interrupt+0x1a/0x20
<4> [default_idle+0/85] default_idle+0x0/0x55
<4> [default_idle+44/85] default_idle+0x2c/0x55
<4> [cpu_idle+88/109] cpu_idle+0x58/0x6d
<4> [start_kernel+722/729] start_kernel+0x2d2/0x2d9
<3>handlers:
<3>[pg0+542356459/1070003200] (usb_hcd_irq+0x0/0x57 [usbcore])
<3>[pg0+542843268/1070003200] (nv_interrupt+0x0/0x89 [sata_nv])
<0>Disabling IRQ #10
<6>ata4: SATA link down (SStatus 0)
<6>scsi3 : sata_nv


Thanks for your help ;-)

Jean-Paul